軟管泵主要有泵殼、轉子體、減速機、機座和軟管等5大部分組成。泵的耐久性主要決定于管子的彈性和耐腐蝕性，其流量與電動機的轉速和管子內徑大小有關。

The hose pump is mainly composed of 5 parts: pump casing, rotor body, reducer, base and hose. The durability of the pump is mainly determined by the elasticity and corrosion resistance of the pipe, and its flow rate is related to the speed of the motor and the inner diameter of the pipe.

軟管泵設備拆除與維護

1、保存好每零件和調換相同零件，在拆檢泵時，應保存好每個零件，要特別注意隔爆零件的隔爆面不能使其損傷拉毛包括絕緣襯墊及套管，如有損壞，必須調換上新的相同零件，不得采用低于原材料性能的代用材料或原有規格不符的零件，裝配時應將所有零件按原先位置裝好，不能遺漏。
2、成纖維、注意保存電動抽油泵應放于干燥，清潔和沒有腐蝕性氣體的環境中。
如果你在使用過程中知道如何更好的保養,那么在它工作過程中，才能更好的提高我們的工作效率.根據我們多年的實踐經驗來說,實現泵的長期有效性可以同時避免因?yàn)檫^多的更換而造成我們投資成本,勞動力的增大,所以我們應切忌要有方法的去操作。

工業軟管泵輸油不足的可能原因及解決方法齒輪泵故障排除10個隔油環齒輪泵應能連續供油，齒輪嚙合重疊系數應大于1。當一對齒輪未脫離嚙合時，另一對齒輪已進入嚙合狀態。這樣，當有兩對齒輪同時嚙合時，兩對齒輪的齒嚙合線之間形成一個封閉的體積，其中部分油也被困在其中。

Possible causes and solutions for insufficient oil delivery of industrial hose pumps. Gear pump troubleshooting. 10 oil-separating ring gear pumps should be able to supply oil continuously, and the gear meshing overlap factor should be greater than 1. When one pair of gears is not disengaged, the other pair of gears has entered the meshed state. In this way, when there are two pairs of gears meshing at the same time, a closed volume is formed between the tooth meshing lines of the two pairs of gears, and part of the oil is also trapped therein.